Non-towered · Class G at the surface
Rockingham County Nc Shiloh (KSIF) radio calls
Reidsville, NCICAO KSIF · FAA SIF
Rockingham County Nc Shiloh is a non-towered airport in Reidsville, NC. Nobody clears you to do anything: you self-announce on the CTAF, 122.8, as Rockingham County Nc Shiloh Traffic, with the airport name at the start and end of each call. The approach control for the area is Greensboro Approach on 124.35, which is who you call for VFR flight following.
No Class B, C, D or E surface area is designated for this airport in the FAA data, so the airspace at the surface is Class G.
Frequencies
| CTAFRockingham County Nc Shiloh Traffic | 122.8 |
|---|---|
| Approach / DepartureGreensboro Approach | 124.35 |
Airport
- Runways
- 13 · 31
- Elevation
- 694 ft
- Position
- 36.437, -79.851
Non-towered airport: self-announce on the CTAF
Sample calls at KSIF
Rockingham County Nc Shiloh has no operating control tower. Every call below goes out on the CTAF, 122.8, to the other aircraft, not to a controller. The runway shown is 13; use whichever runway the wind and the traffic dictate on the day.
The aircraft is the AIM’s own example, Cessna Three One Six Zero Foxtrot; the squawk codes, altitudes and headings are illustrative. Frequencies, station names and runway numbers are this airport’s, from the FAA data.
- Tune 122.8. Nobody clears you; you announce and you listen. The airport name goes at the start and the end of every call, and the runway is always a number, never "the active" (AIM 4-1-9 g 8).
- YouRockingham County Nc Shiloh traffic, Cessna Three One Six Zero Foxtrot, taxiing to runway one three, Rockingham County Nc Shiloh.
- YouRockingham County Nc Shiloh traffic, Cessna Six Zero Foxtrot, departing runway one three, departing the pattern to the north, Rockingham County Nc Shiloh.
- Announce until you are about 10 miles out; on the way back, start announcing at 10 miles (AIM 4-1-9 c 1, TBL 4-1-1).
- YouRockingham County Nc Shiloh traffic, Cessna Three One Six Zero Foxtrot, one zero miles south, two thousand five hundred, landing Rockingham County Nc Shiloh, Rockingham County Nc Shiloh.
- YouRockingham County Nc Shiloh UNICOM, Cessna Six Zero Foxtrot, one zero miles south, request wind and runway information, Rockingham County Nc Shiloh.
- A UNICOM operator, if one is on, answers with the wind and the runway in use (AIM 4-1-9 h). If nobody answers, choose the runway from the wind and the pattern traffic you can hear.
- YouRockingham County Nc Shiloh traffic, Cessna Six Zero Foxtrot, entering left downwind runway one three, full stop, Rockingham County Nc Shiloh.
- YouRockingham County Nc Shiloh traffic, Cessna Six Zero Foxtrot, left base runway one three, Rockingham County Nc Shiloh.
- YouRockingham County Nc Shiloh traffic, Cessna Six Zero Foxtrot, final runway one three, full stop, Rockingham County Nc Shiloh.
- YouRockingham County Nc Shiloh traffic, Cessna Six Zero Foxtrot, clear of runway one three, Rockingham County Nc Shiloh.
If things change. Want flight following after departure? Call Greensboro Approach on 124.35 once clear of the pattern: identification, type, position, altitude, destination, "request VFR flight following" (AIM 4-1-18 a 3). Do not use "any traffic in the area, please advise"; the AIM says it is not to be used under any condition (AIM 4-1-9 g 1).
Phraseology from AIM 4-1-9 c 1, g 1, g 8, h; TBL 4-1-1; 4-3-3. What TowerTalk grades against →
The calls you will make here
Nearby in North Carolina
- W88Air Harbornon-towered
- N83Ds Butler Farm and Airfieldnon-towered
- N63Meadow Brook Fieldnon-towered
- KGSOPiedmont Triad Internationaltowered
- 6W4Yanceyville Municipalnon-towered
- KINTSmith Reynoldstowered
Frequencies, runways and airspace from the FAA National Airspace System Resources (NASR) 28-day subscription, cycle effective Sep 3, 2026. Training use only. Always verify against a current Chart Supplement and sectional chart before flight; frequencies change. TowerTalk is not affiliated with the FAA. Report a discrepancy.
This page is in release tier 2 and is not yet submitted to search engines.
